Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Aurora?
Gate motor and opener replacement in Aurora typically runs $600 to $1,900 for a residential swing or slide gate, with the average job landing near $1,100. A budget residential opener like a Mighty Mule or Ghost Controls unit with a straightforward install sits at the low end, while a commercial-grade FAAC, BFT, or DoorKing system with new wiring and safety sensors pushes toward the top. Manual-gate conversions and severe operator failures with damaged arms or track can climb higher, but the written estimate always sets the final price.
We’re gate specialists, not generalists. Every job on our schedule is a gate job, which is why we can tell you on the phone what a LiftMaster or Linear unit likely needs before anyone rolls out. Our technicians have up to experience across residential and commercial gate systems, and we know your brand. Call (877) 330-0618 for a free estimate, and we’ll give you a real range for your specific gate.
Gate Motor & Opener Cost Breakdown (2026)
Here’s what Aurora homeowners and property managers typically see for the parts and labor on a gate motor project. Ranges reflect standard residential and light-commercial gates within Aurora’s market. Final pricing depends on the exact model, gate weight, and existing wiring.
| Line Item | Typical 2026 Range (Aurora) |
|---|---|
| Residential swing opener (Mighty Mule, Ghost Controls, Linear class), supplied and installed | $600 – $1,100 |
| Residential slide opener (LiftMaster, Elite class), supplied and installed | $900 – $1,500 |
| Commercial-grade swing/slide operator (FAAC, BFT, DoorKing, Viking), supplied and installed | $1,400 – $1,900+ |
| Operator arm or actuator replacement only (existing motor reused) | $250 – $550 |
| Control board or receiver replacement | $180 – $450 |
| Safety sensor pair (photo-eye or edge sensor), supplied and installed | $150 – $350 |
| Battery backup (where compatible) | $120 – $280 |
| New low-voltage wiring run to operator (per 25 ft, depends on trench length) | $200 – $550 |
| Keypad, remote programming, or access control integration | $80 – $300 |
| Manual-to-automatic gate conversion (brackets, operator, sensors) | $800 – $1,700 |
| Full gate + operator installation (new gate and motor together) | $2,500 – $5,500+ |
Two things push the price up fast. The first is gate weight and length. A long, heavy-slide gate in a custom subdivision off Smoky Hill Road needs a bigger operator, a stronger drive, and often a heavier-duty control board than a small residential swing gate. The second is existing site conditions. If the gate posts are set but the conduit doesn’t exist, running new low-voltage lines adds labor and materials that a clean retrofit avoids. On the flip side, when the existing operator just needs an arm, a board, or a sensor pair, reusing the working motor is typically far cheaper than a full swap. That’s the kind of judgment call a gate-only shop makes correctly the first time.
We work up and down the complexity ladder all day, from a Mighty Mule on a single driveway to a DoorKing barrier on a commercial lot. Because we handle both gate repair and new installation, you don’t need a different company as your needs grow.
What Affects Gate Motor & Opener Pricing in Aurora
Aurora is a large, spread-out city with everything from tight infill driveways near Del Mar Parkway to wide commercial entries off East Colfax Avenue, and the gate on each lot drives its own pricing. Here’s what shifts the number most.
- Gate weight and material. A light aluminum residential swing gate takes a lighter-duty opener than a heavy steel slide gate. The operator has to match the gate, so a heavier gate usually means a heavier motor and a higher cost.
- Swing vs. slide. Swing openers are generally less expensive to install because the mount is simpler. Slide gates need a track, a drive gear, and enough run length, which usually adds to the project.
- Brand and grade. Entry-level residential units (Mighty Mule, Ghost Controls) sit at the bottom of the range. Professional and commercial systems (LiftMaster, FAAC, BFT, DoorKing, Viking, Elite, Linear) cost more but are built for heavier gates and more cycles. We service all of them, so the brand you have or want determines the number, not what we’re willing to touch.
- Existing wiring and power. If the gate has a live circuit and conduit in place, labor is lower. If we’re adding a new run or the site needs a power run to the gate, expect the pricing to climb.
- Safety devices and access control. Photo-eyes, edge sensors, keypads, and loop detectors are required for most automatic gate systems and add to the total. They’re also the parts most often missing or failed on older Aurora installations.
- Gate condition and post integrity. A sagging gate, a post pulling out of the ground, or a slide track that’s out of line has to be addressed before a motor goes on, because a new operator on a misaligned gate will fail early.
Frost movement and the freeze-thaw swings along the Front Range shift gate posts and heave slide tracks seasonally, which is one reason Aurora gate hardware takes a beating. That’s a gate issue we see regularly here, and it affects what a motor replacement actually needs to include. Our Aurora page covers the local conditions in more detail.
How to Save on Gate Motor & Opener
There are real ways to keep the cost down without cutting corners on safety or reliability. These are the ones that matter most on a gate motor project.
- Fix the gate before the motor, not after. If the gate sags, drags, or binds, correct that first. A properly aligned gate lets an operator run smoothly and last, which saves you a second repair later.
- Repair the operator if it’s repairable. A control board, actuator arm, or sensor swap is usually far cheaper than a whole new motor. We diagnose what actually failed before recommending a replacement.
- Match the motor to the gate once. Buying an undersized opener to save a few hundred dollars usually means replacing it sooner. The right system costs more upfront and less over time.
- Bundle the safety devices with the install. Adding photo-eyes and a keypad during a motor replacement is cheaper than adding them a year later when you’re paying separate labor.
- Get a free written estimate before anyone starts. We give you an itemized range up front, and the written estimate sets the final price. Call (877) 330-0618 for a free estimate.
We’re not the cheapest quote in town, and we don’t try to be. What we offer is correct diagnosis on the first visit, the right parts for your brand, and a fix that holds up through Aurora’s seasons. That’s how you actually save money on a gate motor.
Can a Gate Motor Be Replaced Without Replacing the Whole Gate?
Yes, in most cases the gate stays and only the operator and its accessories are replaced. Gate panels last far longer than the motor and control electronics inside them, so an operator swap on a sound gate usually costs a fraction of a full gate-and-motor install. The gate needs to be inspected for alignment, post stability, and hinge condition first. If the gate is sound, a motor replacement is a one-visit job for most residential systems, and often for commercial ones too. Call us for a free estimate and we’ll tell you honestly whether you need a motor, a repair, or both.
How Long Does a Gate Motor Installation Take in Aurora?
Most residential gate motor installations in Aurora take about half a day to a full day, depending on wiring and site conditions. A straightforward replacement of an existing operator is usually the shorter job. A manual-to-automatic conversion or a full new install with new wiring and safety devices takes longer because more parts go in and more has to be tested. Commercial systems can run longer still. Fast dispatch from 7am to 7pm, Sunday through Friday, means we get to the job and get it done without dragging it across multiple visits when the work doesn’t demand it.
Does Every Motor Brand Cost the Same in Aurora?
No. Brand and grade change the price, often by several hundred dollars. Entry-level residential systems like Mighty Mule and Ghost Controls are built for lighter gates and lower cycle counts, and they cost less. Professional and commercial systems like LiftMaster, FAAC, BFT, DoorKing, Viking, Elite, and Linear cost more but handle heavier gates, more cycles, and integration with access control. We service all nine brands, so we’re not steering you toward one. We match the motor to the gate and the use, and we tell you what each tier actually gets you. If you want the technical breakdown, our gate opener repair page walks through how each system type behaves over time.
Can a Gate Motor Be Installed on a Manual Gate?
Yes, and it’s one of the more common upgrades we handle. A manual gate conversion means adding an operator, mounting brackets, and safety devices to a gate that currently opens by hand. The gate must be in good working order first: swinging freely, aligned, and hung on solid posts. Conversion pricing in Aurora typically runs $800 to $1,700 depending on gate type, operator choice, and whether new wiring is needed. It’s usually less than a full new gate install, and much less than replacing a failing automatic gate later. If you’re not sure whether your gate can be automated, call (877) 330-0618 and we’ll talk it through.
Which Gate Motor Problems Are Cheapest to Fix?
The cheapest gate motor fixes are usually sensor faults, remote and keypad issues, and battery problems, often running $80 to $350. The most expensive are failed control boards and worn actuators, which can run from a few hundred dollars to over $1,000 depending on the brand and system. A gate that won’t open isn’t always a dead motor. A misaligned sensor, a dead battery in the remote, or a tripped safety edge will stop a gate just as completely as a failed drive. That’s why we diagnose before we quote. A correct diagnosis on the first visit is what separates a $150 fix from a $1,500 replacement.
Are Electric Gate Motors Dangerous to Work On?
Yes, an automatic gate operator carries real hazards: line-voltage electrical connections, stored mechanical force, and heavy gate panels that can crush hands or injure anyone standing in the path. We don’t recommend homeowners open the operator housing or touch the wiring. Leave that to a trained technician who knows your specific brand and system. What you can safely check yourself is external: whether the gate moves freely by hand, whether the safety photo-eyes are blocked or dirty, whether the keypad or remote has power, and whether the gate looks out of line on its track or hinges. If any of those look wrong, don’t force the gate. Call us. We answer 24/7 and dispatch trained technicians across Aurora.
Same-Day Gate Motor Repair in Aurora
When a gate motor fails, you don’t want to wait a week. We provide same-day service on most in-town gate motor calls and fast dispatch from 7am to 7pm, Sunday through Friday. We answer 24/7, and a call outside dispatch hours is booked into the next opening. We’re closed on Saturday. When you call, tell us the brand and model if you know it. That’s the single fastest way to speed diagnosis, because we already know the common failure points on every brand we service.
What to Expect When You Call
- We answer the phone. Tell us the gate type (swing or slide), the brand, and what it’s doing (or not doing).
- We give you a range. Based on the brand and the symptom, we’ll tell you a likely price range before anyone arrives.
- We come out and inspect. The technician checks the gate, the operator, the wiring, and the safety devices. Fast dispatch from 7am to 7pm, Sunday through Friday.
- We write the estimate. Itemized, clear, with a final price. The written estimate sets the price. No surprises.
- We do the work. Repair, motor replacement, or full installation, completed correctly for your system and brand.
Gate Motor Repair and Installation Brands We Service in Aurora
We work with every major gate brand used in Aurora homes, HOAs, and commercial properties: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Each one has its own control logic, programming quirks, and common failure points, and we know them. That’s the benefit of being a gate-only shop. When your gate motor needs attention, you get a technician whose entire expertise lives inside the gate category, not a general handyman learning your system on arrival.
Whether you’re on a residential street near Del Mar Parkway, in a newer subdivision off Smoky Hill Road, or managing a commercial lot along East Colfax Avenue, we cover the full range from budget DIY-tier openers to professional access control. If you’re also considering a new install, our new gate installation service covers the full lifecycle, from the first repair to a full new installation.
FAQs – Gate Motor & Opener Cost
How much does a gate motor cost in Aurora in 2026?
Most residential gate motors in Aurora run $600 to $1,100 supplied and installed, with the average job around $900. Commercial-grade operators for heavier gates run $1,400 to $1,900 and up. The gate’s weight, type, and the brand you choose all move that number. Call (877) 330-0618 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate motor?
Repair is usually cheaper when the failure is in the arm, board, or sensor, running $150 to $550 versus $600 to $1,900 for a full replacement. Replacement wins when the motor itself is burned out or the operator is undersized for the gate. Call (877) 330-0618 and we’ll diagnose it honestly before recommending either.
Can you install a new gate motor on my existing gate?
Yes, in most cases. Residential gate motor installations in Aurora typically run $600 to $1,100 on an existing gate, and the gate itself usually stays. The gate must be sound and aligned first. If it isn’t, we’ll tell you what it needs before the motor goes on. Call (877) 330-0618 for a free estimate.
How much does a gate opener cost for a commercial gate in Aurora?
Commercial gate operators in Aurora typically run $1,400 to $1,900 and up for FAAC, BFT, DoorKing, or Viking-class systems. Heavier gates and added access-control hardware push toward the higher end. Call (877) 330-0618 for a written estimate for your specific site.
Do you service all gate motor brands in Aurora?
Yes, we service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers entry-level residential units through commercial access control systems. Call (877) 330-0618 and tell us your brand – we’ll know what to look for.
Can you come today for a gate motor problem?
Same-day service is available on most in-town gate motor calls in Aurora, with fast dispatch from 7am to 7pm, Sunday through Friday. We answer 24/7. Call (877) 330-0618 and we’ll get you booked for the next opening.
How much does it cost to convert a manual gate to automatic?
Manual-to-automatic gate conversions in Aurora typically run $800 to $1,700, including the operator, brackets, and safety devices. The gate must be in working order first. Call (877) 330-0618 for a free estimate on your specific gate.
Get a Free Gate Motor & Opener Estimate in Aurora
A failing or dead gate operator gets more expensive the longer it sits, and guessing at the fix usually costs more than a proper diagnosis. We’re a gate-only shop with technicians who’ve worked on the full range of residential and commercial systems, and we know your brand. Call (877) 330-0618 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Tell us your gate type and brand, and we’ll give you a real range and a written price before any work begins.
Pricing reflects the Aurora market as of 2026. Aurora Gate Repair offers free estimates – call (877) 330-0618.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Jeff Gallagher"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Luis Castillo"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Danielle Hayes