Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Aurora?
Gate access control in Aurora typically costs $450 to $2,400 for a residential system, with most single-gate keypad or remote entry setups landing near $850 to $1,600 installed. Commercial access control that ties a gate into a networked entry system with card readers or vehicle detection runs $1,800 to $6,500 depending on how many points of control you need. Those are estimated ranges for the Aurora market in 2026, and the written estimate you get after we look at your gate sets the final price.
Access control is where a gate stops being a moving barrier and becomes a system: the operator that moves it, the device that tells it to open, and the wiring and logic that connect the two. That combination is why pricing spreads so wide. A basic keypad on a swing gate is a real upgrade but a modest one. A commercial slide gate that verifies a vehicle with an inductive loop, logs every entry, and lets a property manager open it from a phone is a different project entirely.
We work on gates for a living. Every job on our schedule is a gate job, which means the technician who arrives already knows the operator family, the control board, and the entry devices that are likely bolted to your post. If you’re searching for dependable gate repair, this page will give you the numbers before you call.
Key Takeaways
- Residential access control in Aurora usually runs $450 to $2,400 installed, most often $850 to $1,600.
- Commercial systems with multiple entry points and networking run $1,800 to $6,500.
- The single biggest cost driver is whether your gate already has a working operator. If it does, you’re adding control. If it doesn’t, you’re adding a motor, a board, and safety devices too.
- We’re familiar with nine major gate brands, from Mighty Mule and Ghost Controls at the residential end up through FAAC, BFT, DoorKing, Viking, LiftMaster, Linear, and Elite on the commercial side.
- Estimates are free. Call (877) 330-0618. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Access Control Cost Breakdown (2026)
The table below shows estimated 2026 ranges for the components that make up a gate access control project in Aurora. These are typical ranges; the written estimate confirms your number.
| Item | Estimated Range | Notes |
|---|---|---|
| Keypad entry (wired) | $250 – $650 installed | Adds a code-based entry point to an existing operator |
| Wireless keypad | $180 – $450 installed | Good fit where pulling wire to the post is costly or disruptive |
| Remote receiver plus remotes | $150 – $400 | Depends on receiver type and number of remotes |
| Card reader / proximity reader | $450 – $1,200 per reader installed | Commercial-grade, often multifamily or parking access |
| Intercom or video entry station | $600 – $2,000 installed | Wiring distance and station count push this up or down |
| Inductive loop vehicle detector | $500 – $1,100 installed | Common on commercial slide gates, requires saw-cutting the drive |
| Photoelectric safety sensors | $200 – $450 installed | Required for reliable operation; protects vehicles and people |
| Control board replacement | $350 – $900 | Brand and board generation matter here |
| Smartphone / Wi-Fi module | $200 – $550 installed | App control on a residential operator; depends on the operator’s compatibility |
| Full residential access control package | $850 – $1,600 | Keypad, remotes, sensors, and wiring on an existing operator |
| Full commercial access control package | $1,800 – $6,500 | Multiple readers, loop detection, networking, entry stations |
What pushes a number toward the top of those ranges? Distance is one. Running wire from a house to a gate 150 feet up a slope costs more than a short run across a flat driveway, and it costs more on Aurora’s hard, expansive clay than it does on looser ground, because trenching in that soil is slower work. Device count is another: two card readers and an intercom roughly double the control side of a project compared with one keypad. Brand and board generation matter too. A DoorKing or FAAC commercial board is a different price line than a residential Mighty Mule board, and the entry devices that pair with each are priced differently.
What pulls a number down? A gate that already has a healthy operator, a control board that accepts an add-on keypad or receiver, and a straight wire run. In that situation you’re paying for entry hardware rather than a whole control system, and the project stays modest.
What Affects Gate Access Control Pricing in Aurora
Six things move the number on a gate access control estimate more than anything else.
- Whether an operator already exists. Adding entry control to a working operator is one kind of project. Adding access control where the gate is manual means installing the operator and its safety devices first, which adds a significant line to the estimate.
- Gate type: swing or slide. Aurora properties vary a lot here. A residential swing gate on a driveway is the common case and tends to cost less to automate. A heavy commercial slide gate needs a different operator and usually loop detection, so the control side grows.
- Wiring distance and soil. Wire runs are priced by length and difficulty. Aurora’s clay holds moisture in spring and hardens in summer, and trenching through it takes longer than digging sand. A long run across a lot is a real cost line, not a footnote.
- Entry device count and type. One keypad is one thing. A keypad, two card readers, an intercom, and a phone module is another. Each device adds hardware and its own wiring or pairing work.
- Power at the gate. If there’s no nearby power source, getting power to the operator becomes part of the job. This is common on rural-edge properties east of Aurora where lots are larger and the gate sits far from the house.
- Brand and system age. A board that’s still supported by the manufacturer gives you options. An older board where parts are hard to source sometimes makes a board replacement or a brand-specific upgrade the smarter path. We work across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the recommendation is matched to your specific system rather than fitted to whatever we happen to stock.
One local note worth raising: Aurora sits at elevation along the Front Range, and the freeze-thaw cycle here works on gate hardware and on the ground the posts sit in. Posts that shift or lean change how the gate closes, and an operator doing extra work to force a misaligned gate shut will wear faster. A control upgrade on a gate that’s out of alignment is money spent on top of a problem. We check the mechanical side as part of an Aurora gate estimate so the control system you pay for starts on a sound gate.
How to Save on Gate Access Control
The biggest savings come from deciding what level of control you actually need before any hardware is specified.
- Start with one entry point. A single well-placed keypad handles most residential needs. Add readers or intercoms only when the property genuinely requires them.
- Use wireless where wire is the expensive part. A wireless keypad or receiver can be a sensible choice when the run from the house to the gate is long, and it can save real money on trenching and wire.
- Keep an operator that’s working. If your existing operator is healthy and its board accepts add-ons, build the control system onto it rather than replacing it. Brand knowledge pays off here: knowing which add-on fits a given LiftMaster or Linear board keeps the parts list short.
- Fix alignment before adding control. A gate that closes poorly makes any control system work harder. Correcting hinges, stops, or a leaning post is cheaper than replacing an operator that burned out pushing a misaligned gate.
- Ask for one written estimate that separates parts and labor. It’s easier to trim a scope when you can see what each line costs.
Free estimates are the simplest savings tool. Call (877) 330-0618 and we’ll walk the gate, identify the operator and entry devices, and give you a written number. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Repair or Replace? How to Decide on Access Control
Repair usually wins when the operator motor is sound and the fault is in the control side: a failed receiver, a dead keypad, a board that’s repairable, or wiring damaged by weather or a trimmer. Those are component-level fixes and they cost a fraction of a new system.
Replacement starts to make sense when the operator itself is at the end of its life, when the board is obsolete and no compatible entry devices will pair with it, or when safety sensors can’t be made to work reliably. On commercial systems, a control board that no longer talks to modern readers is often the point where upgrading the control layer makes more sense than patching it again.
The honest answer depends on your brand and model. A Mighty Mule operator with a failed receiver is usually a straightforward fix. A commercial DoorKing or FAAC system with a failing board raises different questions about what the rest of the system will support. Our technicians have up to experience across those brand families, and diagnosing electric gate problems correctly the first time is the whole point of hiring a gate specialist rather than a generalist.
What Happens When You Call
We ask what the gate does now: does it open at all, does it open from one device but not another, does it stop partway, does it reverse for no reason. That conversation usually narrows the fault to the operator, the entry device, or the wiring before anyone arrives. Then we schedule a visit and give you a written estimate before any work begins.
For a new access control system, the visit is about the physical setup: gate type, operator model, power, wire paths, and how many people or vehicles need to get through. If you want to understand the full range of what we do, our Aurora Gate Repair page lays out repair, electric gate repair, and installation as one service arc. Builders and developers sourcing an installation partner for a new gate project can call the same number and ask for a site visit.
Safety: What We Won’t Talk You Through
Gate operators carry real force, and the wiring and power behind them can hurt you. Slide gates that come off their track and heavy swing panels can crush. That’s why we don’t walk homeowners through wiring an operator, adjusting safety sensors, or working on powered gate hardware themselves. We’ll explain what a component does and what’s likely wrong, then recommend a trained technician handle the repair. That’s a duty of care, not a sales tactic.
FAQs – Gate Access Control Cost
How much does gate access control cost in Aurora?
Expect $450 to $2,400 for a residential system in Aurora in 2026, with most single-gate keypad and remote setups landing between $850 and $1,600 installed. Commercial systems with multiple readers and networking run $1,800 to $6,500. Call (877) 330-0618 for an exact quote. Estimates are free.
Can I add a keypad to my existing gate operator?
Usually yes, at roughly $180 to $650 installed depending on whether it’s wired or wireless and which operator you have. Most LiftMaster, Linear, and Elite residential operators accept an add-on keypad or receiver. If the operator’s board is older or unsupported, the honest answer may be that a different approach fits better. Call (877) 330-0618 and we’ll tell you what your model supports.
Why is commercial gate access control so much more expensive?
Commercial systems commonly run $1,800 to $6,500 because they add hardware a residential gate doesn’t need: card readers at $450 to $1,200 each, inductive loop vehicle detectors at $500 to $1,100, intercom or video entry stations at $600 to $2,000, and the networking and control logic that ties them together. Every added point of control adds hardware, wiring, and configuration time. Call (877) 330-0618 for a scope and a written estimate.
Is it cheaper to repair the control board or replace the whole system?
Repair is cheaper when the board is the only failed part and a replacement board or a compatible add-on is available, often $350 to $900 for a board replacement. Replacing the system makes more sense when the board is obsolete and won’t pair with modern entry devices, or when the operator itself is worn out. Call (877) 330-0618 and we’ll diagnose which situation you’re in before quoting anything.
Do you work on my brand of gate operator?
We’re familiar with nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers budget residential operators through commercial access control, so the recommendation is matched to your specific system. Call (877) 330-0618 with the brand and model and we’ll confirm before scheduling.
Can you come today?
Same-day visits are often possible in Aurora. Call (877) 330-0618. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening.
Getting a Straight Number on Your Gate
Access control pricing in Aurora comes down to three questions: does your gate already have an operator, how many devices need to talk to it, and how far is the wire run. Answer those and the estimate becomes a short list of line items rather than a guess. We’d rather tell you that a $250 keypad solves your problem than sell you a $3,000 system you don’t need.
Call (877) 330-0618 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Whether it’s a Mighty Mule swing gate on a residential driveway or a DoorKing system at a commercial entrance, we’ll look at the whole setup and give you a written price before any work starts.
Pricing reflects the Aurora market as of 2026. Aurora Gate Repair offers free estimates – call (877) 330-0618.
Written by the team at Aurora Gate Repair.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Jeff Gallagher"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Luis Castillo"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Danielle Hayes