Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Aurora?
Gate installation in Aurora typically costs $1,800 to $7,500 for a residential driveway gate, with a manual single-swing gate at the low end and a sliding gate with an automatic opener at the high end. Most homeowners here land around $3,200 to $5,000 once the operator, safety sensors, and concrete footings are included. Commercial-grade systems that use DoorKing or FAAC access control run higher, usually from $6,000 to $15,000 and up depending on the entry width and the amount of electrical work required.
That’s a wide range, and it’s honest: the spread is real because a basic backyard gate and a full automatic driveway entry on an Aurora lot are two very different builds. What follows breaks the cost down line by line for the 2026 Aurora market so you can see where your money actually goes before anyone hands you a proposal.
Key Takeaways
- Most residential gate installations in Aurora run $1,800 – $7,500; automated driveway gates typically fall in the $3,200 – $5,000 range.
- The gate itself is usually 30 – 40% of the total. Installation, footings, and electrical make up the rest.
- Adding a LiftMaster, Mighty Mule, or Ghost Controls opener generally adds $700 – $2,400 installed.
- Slope, older fencing that has to be tied into, and the distance to a power source are the Aurora-specific factors that move the number most.
- Every quote we give is free and written. The written estimate sets the final price, not a phone estimate or a ballpark.
Aurora Gate Repair is a gate-only operation – we work on products from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and that focus is what lets us give you a realistic range instead of a guess. To get a written figure for your specific gate and property, call (877) 330-0618 and we’ll schedule a free on-site estimate.
Gate Installation Cost Breakdown (2026)
The table below shows typical installed price ranges for the Aurora market in 2026. These are general ranges for planning. A written estimate after we’ve looked at your property is what pins down your actual number, because slope, power access, and existing fencing change the total quickly.
| Line Item | Typical Range (Installed) | What It Covers |
|---|---|---|
| Manual single-swing gate | $1,800 – $3,400 | Gate, hinges, posts set in concrete footings, latch, installation |
| Manual double-swing driveway gate | $3,500 – $6,200 | Two gate leaves, posts, footings, drop rod, hardware |
| Sliding gate, manual | $2,800 – $5,500 | Gate panel, track, support posts, rollers, guide, installation |
| Sliding gate, automated | $5,500 – $11,000 | Gate, track, footings, operator, sensors, control box |
| Automatic swing operator installed | $700 – $2,400 | Operator unit, arm or underground mechanism, safety sensors, basic wiring |
| Electrical run to gate location | $450 – $2,000 | Buried conduit and power from the closest available source to the gate operator |
| Keypad or access control | $350 – $1,200 | Keypad, entry device, wiring, and integration with the opener |
| Loop detector or exit sensor | $400 – $950 | In-ground loop, sensor, and connection to operator |
| Concrete footing work | $250 – $900 | Footings for gate posts and operator, sized for the gate weight |
What drives the number up: a longer gate or wider opening, heavier panel materials, a slope that needs the gate to swing or slide against grade, and long electrical runs where the power source is far from the gate. Automation itself adds more than the gate, and access hardware – keypads, loop detectors, intercom-style entry devices – adds another layer. What keeps costs down: a level entry, a power source close by, existing fencing in good shape that the gate can tie into, and choosing a reliable DIY-tier operator like a Mighty Mule or Ghost Controls unit instead of commercial access equipment you don’t actually need.
If you’d rather see how gate repair pricing stacks up against replacement, a quick visit to Aurora Gate Repair is the easiest way to see what we do across repair, electric gate repair, and installation before you decide.
What Affects Gate Installation Pricing in Aurora
Aurora isn’t a flat, forgiving place to install a gate. The metro area’s mix of new builds, older subdivisions, and lots that back onto open space or drainage creates a few recurring cost drivers we see on almost every estimate.
- The gate’s size, material, and weight. A 4-foot ornamental gate and a 12-foot wrought steel driveway gate are entirely different jobs. Heavier panels need larger posts, deeper footings, and stronger hardware, and the gate itself is usually 30 – 40% of the total.
- Slope and grade on your lot. Aurora properties near the reservoirs and neighborhoods with some elevation often have entries that pitch. A slope changes how a gate swings or slides and can mean custom hardware or a different operator design.
- Distance to power. Almost every automated gate in Aurora needs an electrical source. If a usable circuit is close, the electrical line item is modest. If it’s 80 feet away, that conduit run adds into the $450 – $2,000 range or more.
- Existing fencing and posts. If you’re tying into existing fence, that fence has to line up and be structurally sound. Older or sagging fencing near the gate may need repair so that the new gate and existing panels meet cleanly and stay stable.
- Operator and access hardware. A residential LiftMaster or Linear operator with a keypad is a much different price than a commercial DoorKing entry system with a loop detector and access control. Both are jobs we do, but they’re built differently.
- Permits and site access. Some gate projects need a permit, and many Aurora HOAs have standards for gate style and finish. Ask your city’s building department and your HOA about requirements before work starts – those requirements can add cost. We’ll always advise you honestly about what your project likely needs.
Because our technicians have up to experience and we work only on gates, we can usually tell from an on-site look which of these factors will actually drive your number and which won’t. We answer 24/7, so you can call (877) 330-0618 and get a real conversation about your project.
How We Quote Gate Installation Differently
A pricing guide is only useful if the company giving the numbers actually knows the systems. That’s where a gate specialist matters. When a general contractor prices a gate installation, they often estimate based on what they remember and then adjust once they’re on site. When we price one, we’re working from the brand-specific parts and the operator’s actual requirements – whether that’s a lightweight Mighty Mule arm for a backyard gate or a heavier FAAC or BFT system for a driveway that gets used every day.
The reason this shows up in the price: the wrong operator for your gate means paying for a redo. A DIY-tier opener on a heavy wrought steel gate that was sized for a box store unit wears out fast and fails. Oversizing to commercial equipment on a simple backyard gate means paying for capacity you’ll never need. Matching the equipment to the gate is the single biggest thing we do that affects your total cost.
If you’re dealing with an existing gate and wondering whether to fix or replace it, our Aurora page covers the repair side, and the honest answer is often that a repair is cheaper if the gate is structurally sound and only the operator is failing. If the gate itself is bent, rusted through at the posts, or dragging on the ground, replacement is usually the better long-term call.
How to Save on Gate Installation
Gate installation prices are mostly set by the gate, the operator, and the site. You can’t change Aurora’s slope, but you can make choices that keep your total down.
- Choose an operator matched to the gate. If your gate is a standard residential driveway gate, a LiftMaster or Linear operator is usually the right fit. Commercial-grade equipment has its place, but it isn’t needed for most home gates.
- Keep the gate location close to power if you’re building new. When planning a new fence or gate, position the entry near an existing power source. That one decision can cut the electrical line item substantially.
- Tie into fencing that’s already sound. If your existing fence posts and panels are sturdy and plumb near the gate, that saves footing and panel work. If they’re not, expect that to add cost.
- Decide what the gate is actually for. A back gate for a dog and a full automated driveway entry are different jobs. Decide up front what you need, and the quote stays lean.
- Get more than one estimate, but compare line items. Compare the gate material, operator brand, footing depth, and electrical scope – not just the bottom line. A low number with a weak operator will cost more in two years.
- Ask about the free estimate. You can get a written number at no charge by calling (877) 330-0618. That’s the cleanest starting point.
We don’t pitch maintenance plans or service contracts. Installation is a per-job price set by the written estimate. If you want a one-time tune-up later, we quote that separately after we’ve looked at the gate.
What to Ask Before You Book a Gate Installation in Aurora
A few direct questions separate a good installation partner from a costly surprise later.
- Will you set posts in proper footings? Light footer work that doesn’t hold up over Aurora’s freeze-and-thaw winters means a sagging gate and reinstall costs later. Properly sized concrete footings are non-negotiable.
- How will the operator be powered and wired? Ask exactly how the electrical run will be done. Good work is buried in conduit.
- What brand of operator are you installing, and why? A specialist will know the brand and the part and tell you why that unit fits your gate.
- Do I need a permit, and is it included? Ask your city’s building department about permit requirements. Get clarity in writing about who handles it.
- Are safety sensors included on an automated gate? If the gate has an operator, safety sensors are essential and should be on the quote.
One safety note worth stating plainly: automated gate operators involve electrical wiring, and slide gates carry serious risk if the track, rollers, or operator weren’t properly installed. This isn’t a component to improvise. Hardwired electrical work and the installation of an automatic operator should be done by a qualified installer who knows the safety requirements. On the repair side, if your gate is dragging on its track or comes off the rollers, don’t keep cycling it. A gate that has lost its guide or support is a real injury hazard and should be looked at by a trained technician.
Every job on our schedule is a gate job, so the technician who arrives has spent their work life on gates – not gates as one line item in a general service business. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday. When the estimate is done, you’ll have numbers in writing, not a verbal guess.
FAQs – Gate Installation Cost
How much does a driveway gate cost installed in Aurora?
A residential driveway gate in Aurora typically costs $3,500 to $11,000 installed, depending on whether it’s a swing or sliding gate and whether it’s automated. A manual double-swing driveway gate usually lands in the $3,500 to $6,200 range. Add an operator, sensors, and an electrical run, and an automated driveway entry is usually $5,500 to $11,000. For a written number on your specific gate, call (877) 330-0618 – estimates are free.
How much does an automatic gate opener cost to install in Aurora?
An automatic gate operator installed on an existing gate typically costs $700 to $2,400 for a residential system. The range covers the operator unit, safety sensors, mounting, and basic wiring. The biggest variables are the operator brand and mechanism – an arm-style LiftMaster or Mighty Mule unit for a residential swing gate is at the lower end, while an underground or heavy slide operator sits higher. Call (877) 330-0618 for an exact quote on your gate.
Is it cheaper to repair or replace a gate in Aurora?
Repair is usually cheaper if the gate structure is sound, and replacement is usually the better value if the gate is bent, rusted through at the posts, or dragging. A repair on a working gate with a failing operator might cost a fraction of a new install. But if the gate panel itself is damaged, footing reinstall, new posts, and a new operator can cost more than a fresh install. It’s a judgment call best made on site after looking at the gate. Call (877) 330-0618 for an on-site estimate – it’s free.
Do I need a permit to install a gate in Aurora?
Some gate projects need a permit and some don’t, and the rules can vary by the scope of work and any electrical installation. Most cities require a permit when electrical work is part of the job, and many HOAs have standards for gate style, finish, and setback. Ask your city’s building department directly before work starts, and ask us about what the electrical side will require so it isn’t a surprise. Call (877) 330-0618 to talk through your project.
Can you install a gate the same day?
A full new gate installation is almost never a same-day job – the footings have to be set and cured before the gate and hardware go on. A simple operator replacement or repair on an existing gate can often be done in a single visit. For scheduling and a same-day estimate, call (877) 330-0618. We answer 24/7, and dispatch runs 7am to 7pm, Sunday through Friday.
Which gate brands do you work with?
We work with products from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That spans entry-level residential openers like Mighty Mule and Ghost Controls through commercial-grade access control from FAAC, BFT, and DoorKing. If you already have a brand on your gate, tell us when you call and we’ll tell you what we can do. Call (877) 330-0618.
What Happens When You Call
We answer 24/7. When you call (877) 330-0618, tell us the gate type (swing or slide), whether it’s automated, and the brand of the operator if you know it. We’ll ask a few questions about the property – slope, power access, existing fence – and then book an on-site estimate. Fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
The estimate is free, the quote is in writing, and the written estimate sets the final price. Our technicians have up to experience, and every job on our schedule is a gate job. If your gate has failed or you’re planning an install, call (877) 330-0618. We’ll give you real numbers for your Aurora property, not a guess.
Written by the team at Aurora Gate Repair.
Pricing reflects the Aurora market as of 2026. Aurora Gate Repair offers free estimates – call (877) 330-0618.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Jeff Gallagher"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Luis Castillo"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Danielle Hayes