Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Aurora?
Most gate repairs in Aurora run between $150 and $650, with a typical residential fix landing near $275. Manual gates sit at the low end: a sagging hinge, a bent latch, a post that needs resetting. Automatic and electric gates push higher, usually $300 to $900, because the work involves the operator, the wiring, and the safety sensors on top of the gate itself. A full operator replacement or a heavily damaged commercial slide gate can pass $1,500, but that’s the exception rather than the everyday job.
Those ranges are estimates. The written estimate you get after we’ve looked at your gate sets the final price, and there’s no charge for that estimate. We answer 24/7 at (877) 330-0618, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Typical gate repair in Aurora costs $150-$650, with most residential jobs near $275.
- Electric and automatic gate repairs usually run $300-$900 depending on the operator and brand.
- The gate brand matters: a Mighty Mule DIY swing operator and a DoorKing commercial slide system share almost no parts, and the price reflects that.
- Estimates are free, and repairs are priced per job after we see your system.
- Cold-weather freeze-thaw cycles across the Front Range are a common cause of gate hardware problems in Aurora, so seasonal wear is worth factoring in.
Gate Repair Cost Breakdown (2026)
Here’s how the numbers break down by job type for the Aurora market. These are typical ranges, not fixed prices. Every gate is measured, inspected, and estimated on its own.
| Repair Type | Typical Cost Range | What It Covers |
|---|---|---|
| Manual gate adjustment (sagging, sticking, out of alignment) | $150-$350 | Hinge tightening, latch alignment, post adjustment, hardware replacement |
| Gate hardware replacement (hinges, latches, rollers, tracks) | $175-$450 | Parts plus labor for worn or broken mechanical components |
| Post repair or reset | $250-$700 | Footing adjustment, post straightening, bracket repair; deeper footing work pushes toward the top |
| Electric gate diagnosis and repair | $300-$900 | Operator, control board, wiring, safety sensors, remote and keypad issues |
| Gate operator replacement | $600-$1,500+ | New swing or slide operator, mounting, wiring, and setup |
| Commercial slide gate repair | $400-$1,500+ | Heavy-duty operator service, track and roller work, access control (DoorKing, FAAC, BFT, Viking systems) |
| Full gate installation | Quoted per project | New gate, posts, hardware, and operator if automated |
What pushes a job toward the top of a range? A few things. Rusted or seized hardware that has to be cut out. An operator that’s been failing for a while and took the control board with it. Posts that lost their footing after a season of freeze-thaw. And commercial-grade systems: a DoorKing slide operator uses different components than a residential Linear swing arm, and the parts cost more.
What keeps a job lower? Catching problems early. A gate that’s starting to sag and gets adjusted is a far smaller bill than one that’s been dragging for a year and has worn out the hinges, the latch, and the post bracket. Manual gates stay cheaper across the board because there’s no operator or wiring to test.
For a deeper look at what a repair visit involves, our gate repair page walks through the process from diagnosis to fix.
What Affects Gate Repair Pricing in Aurora
Gate repair pricing in Aurora isn’t random. A handful of factors move the number, and knowing them helps you read an estimate with confidence.
- Gate type and size. A small residential swing gate and a wide commercial slide gate are different jobs. Bigger, heavier panels need more hardware, more support, and more time. Slide gates add track and roller wear on top of everything else.
- Manual versus automatic. Manual gates are mechanical only. Automatic gates bring in the operator, the control board, the safety sensors, and the electrical side, and each of those is a separate point of failure that has to be checked.
- The brand and system. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and the parts across those nine brands are not interchangeable. A budget-friendly Ghost Controls DIY operator and a commercial FAAC swing system need different parts, different diagnostics, and different amounts of time. We know the brand before we arrive, which means fewer wrong guesses and a more accurate estimate.
- Parts availability. Some operators use common components that are easy to source. Others use brand-specific boards or proprietary parts. When a part has to be ordered, that affects timing more than it affects the labor, but it’s worth knowing before the estimate.
- Condition of the gate and posts. Surface problems are quick. Underlying trouble – loose footings, cracked welds, rusted-through mounts – takes longer to correct. In Aurora, the freeze-thaw cycles through fall and winter work posts and hardware hard, and a gate that sat through a rough season may need more than the symptom suggests.
- Access and layout. A gate that’s easy to reach, with clear space to work around it, is a faster job than one tucked into a tight corner or behind landscaping. This is one of the reasons we estimate on-site rather than over the phone.
The electrical side of an automatic gate – wiring, power, the control board – is not a DIY job. If your gate’s operator is dead or its wiring looks damaged, leave the power off and call a trained technician. There’s real risk in live wiring and in heavy panels that can drop or slide unexpectedly.
What Does an Electric Gate Repair Cost in Aurora?
Electric gate repair in Aurora typically costs $300 to $900, and most of that range is tied to which component failed. The operator itself is the big-ticket item. Control boards, sensors, and wiring repairs sit in the middle. Remotes, keypads, and simple limit-switch adjustments sit at the low end.
What we see most often on automatic gates around Aurora comes down to a few recurring problems:
- Operator failure. The motor or gearbox wears out, or a board fails. This is usually the most expensive repair and sometimes the point where replacement makes more sense.
- Safety sensor problems. The gate reverses, stops, or refuses to move because the sensors are misaligned, dirty, or failed. These are often quick fixes and worth checking first.
- Wiring issues. Loose connections, rodent damage, or worn insulation can interrupt signals. Electrical work on a gate operator should be handled by a trained technician.
- Remote and keypad programming. Sometimes the gate is fine and the access control needs reprogramming. Simple fix, small bill.
- Track and roller wear on slide gates. Heavy panels riding worn rollers strain the operator and can derail. Left alone, this turns a small repair into a big one.
The right fix for your specific system beats a generic one every time. That’s the advantage of a gate-only trade: we diagnose your LiftMaster swing arm differently than we diagnose a BFT slide operator, because they fail differently. Getting the diagnosis right the first time is what keeps the final cost where the estimate said it would be.
Does Repairing an Electric Gate Cost More Than Replacing It?
Usually no. A repair in the $300-$900 range is almost always cheaper than a full operator replacement at $600-$1,500 or more. Replacement makes sense when the operator is old, the board and motor are both failing, and parts are hard to source. A technician can tell you which side of that line your gate is on after seeing it.
How to Save on Gate Repair
There’s no magic discount on gate repair, but a few practical habits keep the bill down in Aurora.
- Fix symptoms early. A gate that sticks, drags, or hesitates is telling you something. Adjusting it now is a $150-$350 job. Waiting until the hardware or the operator gives out can double or triple that.
- Know your brand. Have the operator’s brand and model ready when you call. If you can, snap a photo of the operator housing and the control board. We work on nine major brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and knowing the system up front means a faster, more accurate estimate.
- Keep the gate and track clear. Debris, overgrown landscaping, and grit in the track accelerate wear. A quick clear-out now and then is free and saves hardware later.
- Get the estimate in writing. Free estimates mean you can compare the scope and the parts before saying yes. There’s no charge to have us look at your gate and give you a written price.
- Don’t let a small panel problem become a big one. A loose hinge or a warped panel strains the operator on an automatic gate. Small mechanical fixes protect the expensive electrical components.
To set up a free estimate, call (877) 330-0618. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
FAQs – Gate Repair Cost
How much does gate repair cost in Aurora?
Most gate repairs in Aurora cost between $150 and $650, with a typical residential job near $275. Automatic and electric gate repairs usually run $300 to $900, and full operator replacement runs $600 to $1,500 or more. Call (877) 330-0618 for an exact quote – estimates are free.
Is it cheaper to repair or replace my gate operator?
Repair is usually cheaper, at $300-$900 versus $600-$1,500 or more for replacement. If the operator is failing on multiple fronts – board, motor, and sensors – replacement can be the better value. A technician can tell you which makes sense for your system. Call (877) 330-0618 for a free estimate.
How much does electric gate repair cost in Aurora?
Electric gate repair in Aurora typically costs $300 to $900, depending on the component that failed. Sensors and remotes sit at the low end; operator and control board work pushes toward the top. Call (877) 330-0618 and we’ll give you a written estimate.
Can you come today?
Same-day service is often possible. We answer 24/7 at (877) 330-0618, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician out to look at your gate. A call outside dispatch hours is booked into the next opening.
Do you charge for estimates?
No. Estimates are free. We look at the gate, diagnose the problem, and give you a written price before any work starts. The written estimate sets the final price. Call (877) 330-0618 to schedule one.
Do you work on my gate brand?
Yes, if it’s one of the nine we cover: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That spans budget residential DIY operators through commercial access systems. Call (877) 330-0618 and tell us what you’ve got.
Gate Repair in Aurora: What to Expect
Gate work in Aurora spans a wide range, and the price follows the job. Manual gate repairs sit at $150-$650, automatic and electric systems at $300-$900, and full operator replacement can reach $1,500 or more. The thing that keeps a bill accurate is diagnosis: knowing your brand, your operator, and your system before touching it. Our technicians have up to experience, and every job on the schedule is a gate job.
We work on residential and commercial gates alike, and we cover the full range from repair to a new installation. If your needs grow from fixing a broken hinge to adding an automatic operator, that’s the same company across the whole span. For a broader look at our services, visit Aurora Gate Repair.
Get a Free Gate Repair Estimate in Aurora
If your gate is sticking, sagging, reversing, dead, or making a noise it didn’t make last month, it’s worth having a specialist look at it before a small problem gets expensive. Call (877) 330-0618 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll tell you what’s wrong, what it costs, and what the right fix is for your specific system.
Pricing reflects the Aurora market as of 2026. Aurora Gate Repair offers free estimates – call (877) 330-0618.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Jeff Gallagher"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Luis Castillo"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Danielle Hayes