Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Aurora?
Gate parts and welding in Aurora typically run $150 to $650 for common repairs, and most residential jobs land around $220 to $380. A replacement bracket or hinge set with a weld repair at the post usually sits at the low end, while a bent slide-gate track, a re-hung heavy panel, or a welded gate-frame repair pushes toward the top. Every job is quoted before any work starts, so the written estimate you get is the price you pay, not a starting point we drift from.
We’re a gate-only operation, which matters for this kind of work. A gate is a structure, a moving mechanism, and often an automatic system all at once. Getting the parts right and the welding right is what keeps an automatic gate working instead of going crooked a month later. Call (877) 330-0618 for a free estimate. We answer 24/7.
Key Takeaways
- Common gate welding and parts repairs in Aurora: $150-$650.
- Hinge and latch hardware replacement: $120-$280.
- Track straightening or slide-gate repair: $280-$750.
- Heavy commercial gate panel repair: $450-$1,200.
- The written estimate sets the final price, and it’s free.
Gate Parts & Welding Cost Breakdown (2026)
Here’s how the work breaks down on typical Aurora jobs. These are estimate ranges for the Aurora market in 2026, not a quote for any particular gate. When we look at your gate, we put the actual work into a written estimate so you can see the parts and the labor separately before you decide.
| Work Item | Typical Estimate |
|---|---|
| Hinge, bracket, or latch replacement (residential) | $120 – $280 |
| Weld repair on a gate frame or post bracket | $150 – $420 |
| Roller, wheel, and track hardware replacement | $180 – $380 |
| Slide-gate track straightening or re-set | $280 – $750 |
| Swing-gate re-hang and hinge reset | $220 – $520 |
| Welded reinforcement for a sagging or heavy panel | $250 – $580 |
| Operator mounting bracket and welded post reinforcement | $320 – $680 |
| Commercial heavy-duty gate panel repair | $450 – $1,200 |
| Full gate fabrication from a damaged frame (residential) | $900 – $2,400 |
What pushes a job toward the high end? Metal thickness. A thin residential frame welds quickly; heavier tube steel takes longer, more passes, and often a second technician to hold the gate square. Rust that has eaten into a post means we’re repairing metal instead of just attaching to it. A gate that’s out of square means the welding has to pull it back before any hinge will sit right. And on an automatic gate, once the structure is solid again, the operator and its wiring get checked so the gate travels cleanly through its limits.
What keeps cost down? Catching a loose hinge before it rips the frame. Replacing a $15-bearing roller instead of waiting until the roller eats a groove into the track. Fixing one weld while the gate is still hanging straight. Most of the expensive jobs we see started as a small hardware problem a few weeks earlier. The cheapest repair is the one you do before the gate goes crooked.
What Affects Gate Parts & Welding Pricing in Aurora
- Gate material and metal thickness. Aluminum, steel, ornamental iron, and vinyl each weld or fasten differently. Thicker structural steel means more welding time and often the gate has to be braced before it’s worked on. A light aluminum residential gate is a much faster repair than a commercial iron gate.
- Powered vs. manual. On a manual gate, we fix the structure and hardware and stop there. On an automatic gate, we also have to keep the operator, its arms, the safety sensors, and the wiring in mind so the repair doesn’t throw off how the gate opens and closes. Since Aurora Gate Repair works on both, we don’t send you to a second company once the metal is sorted.
- Brand and operator. If your gate runs a LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule system, we already know how that operator mounts and how its brackets take to a repair. Brand-familiar work means fewer return visits and correct mounting hardware the first time.
- Residential vs. commercial. A home driveway gate is one scale. A commercial sliding gate at a parking lot entrance is another: heavier panel, heavier track, larger concrete footing, and more eyebolts holding it all together. Commercial-grade welding and hardware for FAAC, BFT, DoorKing, and Viking systems carries a higher estimate for good reason.
- Rust and prior repairs. Aurora’s dry climate slows rust compared with wetter regions, but sprinkler spray and years of wind-blown grit still wear hinges, rollers, and welds. If a previous repair used the wrong hardware, we may spend part of the job undoing that before we can build the correct fix.
- Access and the surrounding grading. A gate that sits on a slope, in tight gravel, or with a concrete pad that’s cracked will take longer to work around. Footing and track work are also affected by Aurora’s clay-heavy Front Range soil, which shifts with our freeze-thaw cycles and can cause a track to drop or a gate to bind. Proper footing depth and getting the track re-set matters more here than in a place where the ground holds still.
How to Save on Gate Parts & Welding
The single best way to keep a gate repair in Aurora cheap is to have a small problem fixed while it’s small. A hinge that’s starting to loosen is a modest hardware replacement. Leave it until the gate has pulled itself out of square and the same job needs welding to correct the metal. Same gate, very different estimate.
- Get it looked at at the first sign. A gate that’s dragging, a latch that doesn’t catch, a hinge that squeaks louder each week. Waiting is the most expensive choice on the list.
- Keep the track clear. On a slide gate, leaves, gravel, and grit in the track wear the rollers fast. A cleared track saves hardware.
- Address rust early. Touch-up on a rusting spot on a post or frame keeps the metal sound so we’re attaching to it, not replacing it.
- Ask about parts before replacing the whole gate. A damaged frame section or a bent panel is often repairable with the right weld and hardware. Full fabrication is there for the cases where it’s genuinely needed, and it’s a much larger line item.
- Start with a free estimate. A written estimate lets you see the exact parts and labor on your gate before you commit to anything. Call (877) 330-0618 and we’ll put an estimate in front of you.
We don’t quote good, better, best packages. We look at your gate, tell you what’s actually wrong with it, and give you a written estimate on the specific work. If a repair is the right call, that’s what we write up. If the frame has gone too far, we’ll tell you that too, and explain the fabrication or replacement option honestly.
Why Aurora Gate Repair for Gate Parts & Welding
We’re a gate repair and installation specialist, which means every job on our schedule is a gate job. Not a fence, not a general property fix, not a multi-trade handyman call. That focus is why our technicians don’t arrive and figure it out. They arrive knowing the gate category: its brands, its operators, its hardware, and the ways Front Range weather and soil wear a gate down over time.
Our technicians have up to experience, and that experience is entirely in gate work. We work with parts and repairs across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. That range matters because Aurora has the full spread: budget DIY openers on residential Mighty Mule and Ghost Controls systems, mid-range LiftMaster and Linear residential gates, and commercial-grade FAAC, BFT, DoorKing, and Viking systems at apartment and business entrances. We work up and down that complexity ladder, so your gate gets the right fix for its specific system rather than a generic patch.
We cover the whole gate lifecycle. A hinge replacement today, an operator issue next year, a full new installation when the old gate reaches the end of its life. You don’t have to find a second company as your needs change, and you don’t have to explain your gate to someone new each time.
What Does a Gate Parts & Welding Job Involve in Aurora?
A repair job usually starts with a full look at the gate: the structure, the hardware, the track or hinges, and, if it’s powered, the operator and its wiring. We identify the failed part and the cause, not just the symptom. Then comes the work itself, from welding a bracket or frame to replacing rollers, hinges, or a latch. If it’s automatic, we check that the gate runs cleanly through its travel and that the safety pieces still work before we call it done.
New installation, when that’s the right answer, means setting a footing to proper depth for our soil and freeze-thaw conditions, hanging the gate so it clears the ground through every season, and mounting the operator correctly. The gate has to line up with the driveway, the post, and the hardware at the same time. That’s the part brand familiarity really pays off on, whether it’s a residential LiftMaster or a commercial DoorKing.
What Parts Do We Work With?
- Hinges, brackets, and swing-gate hardware
- Rollers, wheels, and slide-gate track hardware
- Latches, stops, and physical locking hardware
- Operator mounting brackets and arms
- Welded frame and post repairs
- Gate frame fabrication where repair isn’t enough
Gate Repair vs. Replacement in Aurora
If the frame is sound and the failure is in the hardware, welding, or a part, repair is almost always the smaller estimate and the better value. Replacing the whole gate because a hinge failed is like replacing a door because the knob went. If the panel itself has rusted through, twisted past the point where it can be pulled square, or been hit hard enough that the metal is failed, replacement or fabrication becomes the honest answer. We tell you which side of that line your gate is on before any work begins.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Aurora?
Gate welding in Aurora typically runs $150 to $580, depending on the metal, the thickness, and how much of the frame needs reinforcing. A single bracket weld is at the low end; a sagging heavy panel with welded reinforcement is at the top. Call (877) 330-0618 for a free estimate on your specific gate.
How much does a replacement gate hinge cost?
A replacement hinge or hinge set in Aurora usually runs $120 to $280 including labor, with the higher end reflecting heavier gate weight or a hinge that has torn the post and needs welded reinforcement. Estimates are free, so call (877) 330-0618.
Is it cheaper to repair or replace a gate?
For most hardware and welding failures, repair is the smaller estimate, often $150 to $650 versus $900 to $2,400 or more for a full new residential gate. Replacement makes sense when the metal itself has failed. Call (877) 330-0618 and we’ll give you a written estimate either way.
Do you weld on automatic gates without messing up the operator?
Yes. We protect the operator, wiring, and sensors before we weld, and we check the gate’s travel and safety pieces once the repair is done. If your powered gate hasn’t been checked in a while, that’s a good reason to have it looked at. Call (877) 330-0618 for a free estimate.
Can you come today?
Same-day service is common in Aurora, with fast dispatch from 7am to 7pm. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday. Call (877) 330-0618 to get on the schedule.
Book a Free Gate Parts & Welding Estimate in Aurora
A drag or squeak today is a much smaller estimate than a bent frame next month. We look at your gate, tell you what’s actually wrong, and give you a written estimate before any work begins. Our technicians know the brands, the operators, and how Front Range weather and soil treat Aurora gates over time, because gate work is all we do.
Call (877) 330-0618 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm. Whether you’re a homeowner dealing with a crooked gate, a property manager with a slow commercial slider, or a builder who needs a reliable installation partner, we’re the call. Gate repair in Aurora starts with one call, and the estimate costs you nothing.
Pricing reflects the Aurora market as of 2026. Aurora Gate Repair offers free estimates – call (877) 330-0618.
Written by the team at Aurora Gate Repair.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Jeff Gallagher"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Luis Castillo"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Danielle Hayes